Go to HPE6-A66 Questions – Try HPE6-A66 dumps pdf [Q14-Q30]

Q14. When a WLAN has to support nomadic devices, a network architect must primarily plan for which component in their design?

Q15. A network designer is documenting the number of physical sites for a customer that is within the scope of a redesign project. When determining the network purpose at each site, on what should the designer focus at each site? (Select two.)

Q16. Refer to the exhibit.

When planning the use of Cat7 cabling for a SmartRate connection between an ArubaOS AP and an ArubaOS switch, which sections should be considered when calculating distance?

Q17. A network architect is creating a new wireless solution for a customer. Wireless coverage is required throughout all four floors of two buildings on the same campus. Dynamic RF capabilities, including AirMatch, are required. Seamless roaming is required within and between the two buildings. Each floor will have approximately 20 APs and 6 external APs are required for connectivity between the two buildings.

Q18. NewStellar has a main corporate campus in a business park with two adjacent buildings. Each building has three floors and each floor is 322 x 175 feet (98 x 53 meters) for 56,350 square feet (5,235 square meters) total. The ceiling for each floor is 12 feet (3.6 meters) high with a drop-down ceiling at 10 feet (3 meters). The network architect has given you one floor to analyze, Building 1 Floor 2, shown in the attached exhibit.

This floor has a central main corridor with washrooms, stairs, elevators and supply and network cabinets. There are cubicles around the perimeter of the floor. The central part main corridor’s dimensions contain 9,350 square feet (870 square meters). Assuming that wireless coverage is not required in the central area, which square footage (square meter) value should a network architect use when determining the number of APs in a capacity design for each floor?

Q19. A customer currently has sets of three Aruba 5406R switches deployed for an access layer in multiple wiring closets in a building They are clustered in a VSF domain The customer wants to set up Multiple Active Detection (MAD) for the OOBM port, as well as use this port for remote management access. To simplify the connectivity, the customer wants to connect these three switches’ OOBM ports to a separate switch in the wiring closet for the OOBM connectivity.
Which would be the most cost-effective solution that would meet the customer’s requirements?

Q20. A network architect plans to implement channel bonding in a new wireless design that involves dense deployment of APs. Which channel width would be optimal for this design?

Q21. A network architect needs to design a new wireless solution for a small company The architect estimates that about 150 APs will be required to implement a capacity design. Roaming support is required. Also, the design requires meshing to connect some of the APs to the network.
The customer requires that client state synchronization be provided for real-time failover.
Which solution would most cost-effectively meet these requirements?

Q22. A company has two buildings on a campus that are approximately 700 feet (214 meters) apart with a clear line of site. No fiber exists between the buildings; however, there is a need for connecting the networks in the buildings together. The connection between the two buildings will need to support peak rates over 1 Gbps.
Which solution should the company choose that will meet their requirements as well as being cost-effective?

Q23. A network architect wants to estimate the number of Aruba APs that will be needed Tor a new wireless design and determine the wireless coverage using VisualRF. The company requires a high-density design. The building has 200.000 square feet. How many APs should the network architect add to VisualRF in order to perform the coverage analysis?

Q24. A network architect is designing a new Wi-Fi solution for a small university The solution will involve two mobility controllers that will be clustered at the campus core Because students use a lot of video in both the dormitory rooms and in the classrooms, the solution will need to support 50Gbps via link aggregation between the controllers and core switches.
Which solution would most cost-effectively meet this requirement for the campus core?

Q25. A network architect is designing a new Wi-Fi solution for a customer The customer currently occupies a one-story building on a small campus. In one part of the building there is an auditorium, where the ceiling height and attenuation is different from the rest of the building. What should the network architect create in VisualRF to identify this difference when planning :ne APs?

Q26. A company needs to replace an existing legacy wireless and wired solution with one that supports features like 802 11 ax for APs and logical switching for switches. The company is located on a single floor with two wiring closets. Assume that there will be 10 APs connected via POE+ to each wiring closet, along with 36 wired user connections All switches on a floor should be configured in a single stack. The distance between wiring closets is 100 feet (31 meters).
Which switching solution will minimally provide 10 Gbps uplinks at the most cost-effective price, while still meeting the company’s requirements?

Q27. A network architect has created two sites in IRIS and defined network devices for each site. From which window would a network architect connect the two sites together?

Q28. A customer requires Aruba switches that support Smart Rate ports to connect to Aruba APs Which switching product should the customer purchase that will provide 24 Smart Rate ports per access layer switch’?

Q29. A network architect is designing a new wired and wireless solution for for a company. The company has two buildings on a campus, which each building has three floors. The campus core will be placed in the basement of Building 1. Each wiring closet has eight strands of multi-mode OM3 grade fiber that connect to a wiring closet of the first floor of the building it is contained, referred to as a main distribution frame (MDF). The maximum distance between a floor’s wiring closet and the MDF is 100 feet (30 meters). The maximum distance between the two MDFs and the campus core is no more than 150 feet (45 meters). There are eight strands of multi-mode OM3 grade fiber from these two MDF closets to the campus core.
Based on this information, which type of design should be used and what is the maximum speeds supported all uplinks for the existing the multi-mode fiber?

Q30. A company is redesigning their wireless network and will be upgrading all devices to support the latest wireless standards. The company is not near any radar installations. In order to keep wireless NIC power levels as low as possible to reduce interference issues and to take advantage of radar frequency ranges, what IEEE standard should APs support?