[Q58-Q80] 2023 Updated NSE5_FAZ-7.0 Tests Engine pdf – All Free Dumps Guaranteed!

admin -

June 23, 2023

5/5 - (2 votes)

2023 Updated NSE5_FAZ-7.0 Tests Engine pdf – All Free Dumps Guaranteed!

Latest NSE 5 Network Security Analyst NSE5_FAZ-7.0 Actual Free Exam Questions

QUESTION 58
Which two of the following must you configure on FortiAnalyzer to email a FortiAnalyzer report externally?
(Choose two.)

Mail server

Output profile

SFTP server

Report scheduling

QUESTION 59
In the FortiAnalyzer FortiView, source and destination IP addresses from FortiGate devices are not resolving to a hostname.
How can you resolve the source and destination IP addresses, without introducing any additional performance impact to FortiAnalyzer?

Resolve IP addresses on a per-ADOM basis to reduce delay on FortiView while IPs resolve

Configure # set resolve-ip enable in the system FortiView settings

Configure local DNS servers on FortiAnalyzer

Resolve IP addresses on FortiGate

https://packetplant.com/fortigate-and-fortianalyzer-resolve-source-and-destination-ip/
“As a best practice, it is recommended to resolve IPs on the FortiGate end. This is because you get both source and destination, and it offloads the work from FortiAnalyzer. On FortiAnalyzer, this IP resolution does destination IPs only”

QUESTION 60
Refer to the exhibit.

What does the data point at 14:55 tell you?

The received rate is almost at its maximum for this device

The sqlplugind daemon is behind in log indexing by two logs

Logs are being dropped

Raw logs are reaching FortiAnalyzer faster than they can be indexed

QUESTION 61
In FortiAnalyzer’s FormView, source and destination IP addresses from FortiGate devices are not resolving to a hostname. How can you resolve the source and destination IPs, without introducing any additional performance impact to FortiAnalyzer?

Configure local DNS servers on FortiAnalyzer

Resolve IPs on FortiGate

Configure # set resolve-ip enable in the system FortiView settings

Resolve IPs on a per-ADOM basis to reduce delay on FortiView while IPs resolve

QUESTION 62
What is the purpose of output variables?

To store playbook execution statistics

To use the output of the previous task as the input of the current task

To display details of the connectors used by a playbook

To save all the task settings when a playbook is exported

FortiAnalyzer_7.0_Study_Guide-Online.pdf page 242: Output variables allow you to use the output from a preceding task as an input to the current task.
“Output variables allow you to use the output from a preceding task as an input to the current task.” FortiAnalyzer_7.0_Study_Guide-Online page 242

QUESTION 63
You crested a playbook on FortiAnalyzer that uses a FortiOS connector
When configuring the FortiGate side, which type of trigger must be used so that the actions in an automation stitch are available in the FortiOS connector?

FortiAnalyzer Event Handler

Incoming webhook

FortiOS Event Log

Fabric Connector event

“One possible scenario is shown on the slide:
1. Traffic flows through the FortiGate
2. FortiGate sends logs to FortiAnalyzer
3. FortiAnalyzer detects some suspicious traffic and generates an event
4. The event triggers the execution of a playbook in FortiAnalyzer, which sends a webhook call to FortiGate so that it runs an automation stitch
5. FortiGate runs the automation stitch with the corrective or preventive actions” FortiAnalyzer_7.0_Study_Guide-Online page 228 In order to see the actions related to the FOS connector, you must enable an automation rule using the Incoming Webhook Call trigger on the FortiGate side. FortiAnalyzer_7.0_Study Guide page no 233

QUESTION 64
Refer to the exhibit.

What is the purpose of using the Chart Builder feature on FortiAnalyzer?

In Log View, this feature allows you to build a dataset and chart automatically, based on the filtered search results.

In Log View, this feature allows you to build a chart and chart automatically, on the top 100 log entries.

This feature allows you to build a chart under FortiView.

You can add charts to generated reports using this feature.

QUESTION 65
Logs are being deleted from one of the ADOMs earlier than the configured setting for archiving in the data policy.
What is the most likely problem?

CPU resources are too high

Logs in that ADOM are being forwarded, in real-time, to another FortiAnalyzer device

The total disk space is insufficient and you need to add other disk

The ADOM disk quota is set too low, based on log rates

Reference:
20logs.htm

QUESTION 66
What is the purpose of employing RAID with FortiAnalyzer?

To introduce redundancy to your log data

To provide data separation between ADOMs

To separate analytical and archive data

To back up your logs

https://en.wikipedia.org/wiki/RAID#:~:text=RAID%20(%22Redundant%20Array%20of%20Inexpensive,%2C%20performance%20improvement%2C%20or%20both.

QUESTION 67
On the RAID management page, the disk status is listed as Initializing.
What does the status Initializing indicate about what the FortiAnalyzer is currently doing?

FortiAnalyzer is ensuring that the parity data of a redundant drive is valid

FortiAnalyzer is writing data to a newly added hard drive to restore it to an optimal state

FortiAnalyzer is writing to all of its hard drives to make the array fault tolerant

FortiAnalyzer is functioning normally

Reference:
8977-00505692583a/FortiAnalyzer-5.6.10-Administration-Guide.pdf (40)

QUESTION 68
Why should you use an NTP server on FortiAnalyzer and all registered devices that log into FortiAnalyzer?

To properly correlate logs

To use real-time forwarding

To resolve host names

To improve DNS response times

QUESTION 69
Which two statements are true regarding log fetching on FortiAnalyzer? (Choose two.)

A FortiAnalyzer device can perform either the fetch server or client role, and it can perform two roles at the same time with the same FortiAnalyzer devices at the other end.

Log fetching can be done only on two FortiAnalyzer devices that are running the same firmware version.

Log fetching allows the administrator to fetch analytics logs from another FortiAnalyzer for redundancy.

Log fetching allows the administrator to run queries and reports against historical data by retrieving archived logs from one FortiAnalyzer device and sending them to another FortiAnalyzer device.

QUESTION 70
Which tabs do not appear when FortiAnalyzer is operating in Collector mode?

FortiView

Event Management

Device Manger

Reporting

QUESTION 71
Which statement correctly describes the management extensions available on FortiAnalyzer?

Management extensions do not require additional licenses.

Management extensions allow FortiAnalyzer to act as a ForbSIEM supervisor.

Management extensions require a dedicated VM for best performance.

Management extensions may require a minimum number of CPU cores to run.

QUESTION 72
When working with FortiAnalyzer reports, what is the purpose of a dataset?

To provide the layout used for reports

To define the chart type to be used

To retrieve data from the database

To set the data included in templates

QUESTION 73
What is the purpose of a predefined template on the FortiAnalyzer?

It can be edited and modified as required

It specifies the report layout which contains predefined texts, charts, and macros

It specifies report settings which contains time period, device selection, and schedule

It contains predefined data to generate mock reports

Reference:
2300_Reports/0010_Predefined_reports.htm#:~:text=FortiAnalyzer%20includes%20a%20number%
20of,create%20and%2For%20build%20reports.&text=A%20template%20populates%20the%20Layout,that%
20is%20to%20be%20created.
https://help.fortinet.com/fa/faz50hlp/56/5-6-2/FMG-FAZ/2300_Reports/0010_Predefined_reports.htm

QUESTION 74
Which two settings must you configure on FortiAnalyzer to allow non-local administrators to authenticate to FortiAnalyzer with any user account in a single LDAP group? (Choose two.)

A local wildcard administrator account

A remote LDAP server

A trusted host profile that restricts access to the LDAP group

An administrator group

QUESTION 75
Which statements are true regarding securing communications between FortiAnalyzer and FortiGate with SSL? (Choose two.)

SSL is the default setting.

SSL communications are auto-negotiated between the two devices.

SSL can send logs in real-time only.

SSL encryption levels are globally set on FortiAnalyzer.

FortiAnalyzer encryption level must be equal to, or higher than, FortiGate.

QUESTION 76
Which two statement are true regardless initial Logs sync and Log Data Sync for Ha on FortiAnalyzer?

By default, Log Data Sync is disabled on all backup devise.

Log Data Sync provides real-time log synchronization to all backup devices.

With initial Logs Sync, when you add a unit to an HA cluster, the primary device synchronizes its logs with the backup device.

When Logs Data Sync is turned on, the backup device will reboot and then rebuilt the log database with the synchronized logs.

QUESTION 77
Consider the CLI command:

What is the purpose of the command?

To add a unique tag to each log to prove that it came from this FortiAnalyzer

To add the MD5 hash value and authentication code

To add a log file checksum

To encrypt log communications

https://docs.fortinet.com/document/fortianalyzer/6.2.5/cli-reference/849211/global

QUESTION 78
FortiAnalyzer uses the Optimized Fabric Transfer Protocok (OFTP) over SSL for what purpose?

To upload logs to an SFTP server

To prevent log modification during backup

To send an identical set of logs to a second logging server

To encrypt log communication between devices

QUESTION 79
Which two elements are contained in a system backup created on FortiAnalyzer? (Choose two.)

System information

Logs from registered devices

Report information

Database snapshot

What does the System Configuration backup include?
System information, such as the device IP address and administrative user information.
Device list, such as any devices you configured to allow log access.
Report information, such as any configured report settings, as well as all your custom report details. These are not the actual reports.
FortiAnalyzer_7.0_Study_Guide-Online pag. 29
FortiAnalyzer_7.0_Study_Guide-Online.pdf page 29: What does the System Configuration backup include?
* System information, such as the device IP address and administrative user information
* Device list, such as any devices you configured to allow log access
* Report information, such as any configured report settings, as well as all your custom report details. These are not the actual reports.

QUESTION 80
If you upgrade your FortiAnalyzer firmware, what report elements can be affected?

Output profiles

Report settings

Report scheduling

Custom datasets

Loading …