Real NACE NACE-CIP1-001 Exam Questions Study Guide [Q37-Q56]

Real NACE NACE-CIP1-001 Exam Questions Study Guide

Updated and Accurate NACE-CIP1-001 Questions for passing the exam Quickly

Do you know how difficult the NACE CIP1-001 certification is to write?

NACE CIP1-001 certification is a difficult exam. The reason behind this is the wide range of topics covered in the exam. The topics are related to the chemical, physical and biological properties of the coatings. You have to be familiar with these properties. The candidates need to prepare for the NACE CIP1-001 test. They can easily download the NACE CIP1-001 exam dumps. The exam dumps contain different kinds of questions that help the candidates to easily pass the NACE CIP1-001 exam. Questions and answers help you to easily prepare for the NACE CIP1-001 exam. A score report helps you to know how much time is required for your preparation. It is very helpful for the candidates to plan their time. Decide the location where you want to sit for the exam. Accurate and concise questions will help you to easily pass the NACE CIP1-001 exam.

NACE-CIP1-001 (Coating Inspector Level 1) Exam is a certification program offered by the National Association of Corrosion Engineers (NACE) International. Coating Inspector Level 1 certification is designed for professionals who work in the field of corrosion protection and coatings inspection. The NACE-CIP1-001 Exam is based on the Body of Knowledge for Coating Inspectors, which covers a wide range of topics including surface preparation, coating application, coating inspection, and equipment maintenance.

NO.37 An exposed area of the substrate or previous coat of a conductive coating material, often caused by poor application technique is called

 cracking.

 sagging.

 holiday.

 checking.

NO.38 The most important factor resulting in improved job site safety is:

 Personal Protective Equipment

 Engineering Controls

 Safety Enforcement

 Situational Awareness

NO.39 Relative humidity is

 a measure of the amount of moisture in the air compared to saturation level.

 a measure of the amount of moisture in the air compared to the air temperature.

 the lowest temperature at which moisture forms on a steel surface.

 the highest temperature at which moisture forms on a steel surface.

NO.40 The form of corrosion that has the largest potential for unexpected catastrophic failure is:

 General Corrosion

 Atmospheric Corrosion

 Galvanic Corrosion

 Localized Corrosion

NO.41 To be of value the Inspector’s documentation must be:

 Always handwritten

 Always typewritten

 Timely, accurate and concise

 Submitted before the end of the job

NO.42 A single application coating film has a measured dry film thickness (DFT) between 4 and 5 mils (between 100 and 125 microns). The volume solids of the coating immediately before application were 67%, What wet film thickness (WFT) was applied?

 5 to 6 mils (125 to 150 microns)

 10 to 12 mils (250 to 300 microns)

 8 to 10 mils (200 to 250 microns)

 6 to 7 mils (150 to 175 microns)

NO.43 The Inspector’s Log Book is generally:

 Retained by the inspector upon project completion

 Submitted to the client upon project completion

 Shared with all parties upon project completion

 Shredded by the inspector upon project completion

NO.44 You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:

 Accept the assignment without hesitation

 Advise the prospective employer that you cannot accept the position

 Meet with the prospective employer to determine the scope of your role

 Review the NACE Attestation prior to making a decision

NO.45 If inspectors identify issues of non-conformance during an inspection, they should

 instruct the contractor’s personnel in how to correct the issue so the project is not delayed

 perform additional tests secretly to ensure there are no other potential issues at the site

 inform both the Contractor and the inspector’s supervisor so they can take appropriate corrective actions

 wait until the final report is being prepared to identify the issues in writing so they are fully documented

NO.46 What is used to determine compressed air cleanliness?

 Needle pressure gauge

 Psychrometer

 Blotter test

 Profilometer

NO.47 SSPC SP 1 identifies the use of:

 Organic solvents

 Inorganic solvents

 Biodegradable detergents

 A wide variety of materials

NO.48 In a non-convertible coating the role of the primary solvent is to:

 To make the coating flow out better

 To dissolve the resin

 To promote faster cure

 To control the evaporation rate

NO.49 On a blast-cleaned surface, Ian ultraviolet light is generally used to detect

 soluble chemical salts

 grease and oil

 inhibitor residues

 sulfates

NO.50 When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:

 Chloride salt may produce a false positive

 Synthetic oil or grease may not be identified

 Ultra-Violet light may contaminant the surface

 Presence of weld spatter may produce a false positive

NO.51 It is good practice for the NACE Inspector to have instrument calibration certificates available:

 At all times

 In the office only

 In the field only

 Only if the specification requires it

NO.52 Which is a component that supplies most of the features and functions of the material?

 pigment

 binder

 solvent

 additive

NO.53 In the event of a conflict between the project specification and the coating manufactures’ product data sheet, the Inspector’s first course of action should be too:

 Call the coating manufacturer for clarification

 Use the product data sheet as a guide

 Use the job specification as a guide

 Call the person who wrote the specification for clarification

NO.54 ISO SA 3 is directly equivalent to:

 NACE No. 1/SSPC SP 5

 NACE No. 2/SSPC SP 10

 NACE No. 3/SSPC SP 6

 None of the above

NO.55 Inspector’s daily reports are used:
Select All That Apply

 By the contractor to estimate the amount of work done that day

 To provide continuity between inspectors

 To aid in arbitration between the contractor and client

 To help in cases of a coating failure

NO.56 Which one of these elements is not necessary for corrosion to occur:

 Anode

 Cathode

 Reference Cell

 Electrolyte

 Loading …

NACE-CIP1-001 certification exam is administered by the National Association of Corrosion Engineers (NACE) International, a non-profit organization that is dedicated to protecting people, assets, and the environment from the effects of corrosion. NACE has been providing corrosion-related education and certification programs for over 75 years, and the NACE-CIP1-001 certification exam is one of their most popular offerings.

Prepare Important Exam with NACE-CIP1-001 Exam Dumps: https://www.dumpstests.com/NACE-CIP1-001-latest-test-dumps.html

Related Links: myportal.utt.edu.tt myportal.utt.edu.tt myportal.utt.edu.tt myportal.utt.edu.tt www.stes.tyc.edu.tw myportal.utt.edu.tt